Electronic and Electro-Hydraulic Controls

HF Electronics Model ECU-0710 – General Purpose Machine Controller for Off-Highway, Mobile Equipment
  PDF file of this page
  HydraForce Electronics Guide (all models) – PDF file
  Electronic Vehicle Controls – Intro. & Contents
  Valve Coils and Valve Controllers – Contents
  Request a quote

ECU-0710 Product image


FEATURES:
• Advanced electronic design for reliability and accuracy.
• Reliable operation in real-world temperature conditions from
–40°C to +70°C (–40°F to +158°F).
• Fully-sealed, compact cast-aluminum housing.
• Inputs and outputs are
protected against shorts.
• Outputs have diagnostic capability.
• No external cooling or heat dissipation required.
• Software developed with
CoDeSys 2.3 Programming Tool.
  DESCRIPTION: The ECU-0710 Machine Controller is a general-purpose programmable controller designed to withstand the real-world environmental demands of the off-highway mobile market. The ECU-0710 can be used as a stand-alone controller, or for integrating into a CAN network with other devices.

Input configuration can be set for up to 20 inputs consisting of Digital, Pulse, Current Measuring Feedback and Analog inputs. Output configuration can be set for a total of 7 outputs consisting of up to 6 PWM or digital high-side drivers, and a single low-side driver. All outputs are capable of driving up to 3.0 Amps.

NOTE: Refer to Input/Output table below for pin configuration capability.
Refer to ECU-0710 Technical Reference Manual for specific data and ratings of individual inputs and outputs.

RATINGS

Power Required:
  Operating Voltage: 9 to 30 VDC; Idle Power Consumption: approx 1 watt;
  Operating Current: 10 Amp max. continuous current, with full external load;
  Over-Voltage: 34 VDC maximum
Reference Voltages: (1) 5 VDC Potentiometer Reference: 200 mA DC
Communication: (2) ISO CAN 2.0B Interfaces: CANopen, J1939, or user-programmable Processing and Memory: Microprocessor: 16-bit at 40 MHz;
  Flash ROM: 254 Kbyte; SRAM: 256 Kbyte; EEPROM: 6200 bytes
Operating Temperature Range: –40°C to +70°C (–40°F to +158°F)
Storage Temperature Range: –50°C to +85°C (–58°F to +185°F)
Water Resistance: meets IP67 standards (per IEC 660529)
Humidity Tolerance: Relative Humidity > 90% from +25°C to +55°C
  (+77°F to +131°F) (per IEC 60068-2-30 Test Db)
Radiated Immunity: 20 to 2000 MHz at 30 V/m (per 2005/83/EC Annex IX)
Vibration: 3.5 Grms random from 10 to 500 Hz (per IEC 60068-2-64 Test Fh)
Shock: 50g peak (per IEC 60068-2-27 and -29 Tests Ea and Eb)
Corrosion: 50 g/l, NaCl for 24 hours at +35°C (per ISO 9227)
INPUTS / OUTPUTS — 20 Total:
Max. I/O
Digital In
(SWG)
Digital In
(SWB)
Pulse
Input
Analog
Input
Current
Feedback
PWM
(Source)
Digital Out
(Source)
Digital Out
(Sink)
6
  X       X X  
2
X   X          
2
  X X          
3
        X      
6   X   X        
1   X           X
20 2 15 4 6 3 6 6 1

NOTE: The ECU-0710 has inputs and outputs that can be configured in multiple ways.
     For more information, consult the ECU-0710 Technical Reference Manual.


DIMENSIONS & MOUNTING:

ECU-0710 Dimensions

The mounting positions shown here will allow water or other potential contaminants to fall away from connectors.

Allow 5 in./125 mm clearance from mounting surface for connector installation.

For additional mounting information, consult the
ECU-0710 Technical Reference Manual.
  PIN ASSIGNMENTS:
Pin Connector 1 Pin Function Type
1
Digital Input/PWM Output/Digital Output I/O
2
Current Measuring Feedback FB
3
Digital Input/PWM Output/Digital Output I/O
4
Digital Input/PWM Output/Digital Output I/O
5 Current Measuring Feedback FB
6 Current Measuring Feedback FB
7 Digital Input/PWM Output/Digital Output I/O
8 Digital Input/PWM Output/Digital Output I/O
9 Digital Input/PWM Output/Digital Output I/O
10 Digital Input/Analog Input Input
11 Digital Input/Pulse Input, 2.2KΩ to +5VDC Input
12 Digital Input/Pulse Input, 2.2KΩ to +5VDC Input
13 Digital Input/Pulse Input, 10KΩ to GND Input
14 Digital Input/Pulse Input, 10KΩ to GND Input
15 Must be left Open N/A
16 +5 VDC Reference (Ref 47Ω)
17 Digital Input/Analog Input Input
18 Digital Input/Digital Output I/O
19 Ground (Ref 47Ω)
20 Digital Input/Analog Input Input
21 Digital Input/Analog Input Input
22 Digital Input/Analog Input Input
23 Digital Input/Analog Input Input
Pin Connector 2 Pin Function Type
1 Power Ground
2 CAN 1 HIGH I/O
3 Power Ground
4 VSUPPLY (+9 to 30 VDC)
5 VSUPPLY (+9 to 30 VDC)
6 CAN 1 LOW I/O
7 CAN 2 HIGH I/O
8 CAN 2 LOW I/O

TO ORDER:
Controller: Model ECU-0710 Part No. 4000351
AmpSeal Connectors: 23-Pin Grey Part No. 4000361; 8-Pin Black Part No. 4000363
AmpSeal Socket/Plug: Sockets Gold (100 pc.) Part No. 4000369; Sealing Plugs (100 pc.) Part No. 4000370
AmpSeal Test Leads: (10 each, 24" length) - Part No. 4000287
Shock Cover Kit (optional): Part No. 4206820
HF-Impulse Programming Software: available from HydraForce Electronics Portal as free download.
USB-CAN Adaptor: Part No. 4000371
Diagnostic Kit: Part No. 4000372