Electronic and Electro-Hydraulic Controls

HF Electronics Model ECU-2415A – General Purpose Machine Controller for Off-Highway, Mobile Equipment
  PDF file of this page
  HydraForce Electronics Guide (all models) – PDF file
  Electronic Vehicle Controls – Intro. & Contents
  Valve Coils and Valve Controllers – Contents
  Request a quote

ECU-2415A Product image

FEATURES:
• Advanced electronic design for reliability and accuracy.
• Reliable operation in real-world temperature conditions from
-40 to 85°C (104 to 185°F).
• Fully-sealed, compact cast-aluminum housing.
• Inputs and outputs are
protected against shorts.
• Outputs have diagnostic capability.
• No external cooling or heat dissipation required.
• Programmed with CoDeSys Programming Tool.
  DESCRIPTION:
The ECU-2415A Electronic Controller is a "next generation" general-purpose programmable controller designed to withstand the real-world environmental demands of the off-highway
mobile market. The ECU-2415A can be used as a stand-alone controller, or for integrating
into a CAN network with other devices.

Input configuration can be set for up to 49 inputs consisting of Digital, Pulse, Current Measuring Feedback and Analog inputs. Output configuration can be set for a total of 24 outputs consisting
of up to 24 PWM or digital high-side drivers. All outputs are capable of driving up to 3.0 Amps.

NOTE: Refer to Input/Output table below for pin configuration capability. Refer to ECU-2415A Technical Reference Guide for specific data and ratings of individual inputs and outputs.

NOTE:The ECU-2415A is a direct replacement for the ECU-2415. It is necessary to convert the CoDeSys program for replacement.

RATINGS
Power Required:
  Operating Voltage: 8.5 to 33 VDC
  Operating Current: 13 Amp max. continuous current, with full external load;
  Idle Power Consumption: approximately 1.5 Watts
  Over-Voltage: 70 VDC maximum maximum (logic / load shutdown circuit at 35 VDC)
Reference Voltages: (1) 5 VDC Potentiometer Reference: 270 mA DC
Communication: (2) ISO CAN 2.0B Interfaces: CANopen, J1939, or user-programmable
Processing and Memory:

  Microprocessor: 16-bit at 100 MHz;
  Flash ROM: 1600 Kbyte; SRAM: 256 Kbyte; NV RAM: 8 kbytes
Environmental Ratings:
  Operating Temperature Range: -40°C to 85°C (-40°F to 185°F);
  Storage Temperature Range: -50°C to 85°C (-58°F to 185°F)
  Water Resistance: meets IP67 standards (per IEC 660529)
  Humidity Tolerance: Relative Humidity > 90% from 25°C to 55°C
  (77°F to 131°F) (per IEC 60068-2-30 Test Db)
  Radiated Immunity: 20 to 2000 MHz at 30 V/m (per 2005/83/EC Annex IX)
  Vibration: 3.5 Grms random from 10 to 500 Hz (per IEC 60068-2-64 Test Fh)
  Shock: 50g peak (per IEC 60068-2-27 Test Ea)
  Corrosion: 50 g/l, NaCl for 24 hours at 35°C (95°F) (per ISO 9227)

INPUTS / OUTPUTS — 49 Total:
Max. I/O
Digital In
(SWG)
Digital In
(SWB)
Pulse
Input
Analog
Input
Current
Feedback
PWM
(Source)
Digital Out
(Source)
Digital Out
(Sink)
1
X              
10
        X      
6
  X   X        
8
X   X          
8   X       X X  
16 X         X X  
49 25 14 8 6 10 24 24 0
NOTE: The ECU-2415A has inputs and outputs that can be configured in multiple ways.
For more information, consult the ECU-2415A Technical Reference Manual.
PIN ASSIGNMENTS:

Pin Connector 1 Pin Function Type
1
Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
2
Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
3
Current Measuring Feedback FB
4
Current Measuring Feedback FB
5 Current Measuring Feedback FB
6 Current Measuring Feedback FB
7 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
8 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
9 Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
10 Current Measuring Feedback FB
11 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
12 Ground
13 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
14 Current Measuring Feedback FB
15 Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
16 Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
17 Current Measuring Feedback FB
18 Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
19 Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
20 Current Measuring Feedback FB
21 Current Measuring Feedback FB
22 Current Measuring Feedback FB
23 Digital I/P; PWM O/P; Digital O/P (no open detect.) I/O
 
Pin Connector 2 Pin Function Type
1 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
2 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
3 Current Measuring Feedback FB
4 Current Measuring Feedback FB
5 Current Measuring Feedback FB
6 Current Measuring Feedback FB
7 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
8 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
9 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
10 Current Measuring Feedback FB
11 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
12 Ground
13 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
14 Current Measuring Feedback FB
15 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
16 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
17 Current Measuring Feedback FB
18 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
19 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
20 Current Measuring Feedback FB
21 Current Measuring Feedback FB
22 Current Measuring Feedback FB
23 Digital I/P; PWM O/P; Digital O/P (open detect.) I/O
  PIN ASSIGNMENTS:

Pin Connector 3 Pin Function Type
1
+ Aux Out (Ref 4A)
2
+5 VDC Reference (Ref 270 mA)
3
Digital Input/ Analog Input, 2.2KΩ to +5VDC Input
4
Digital I/P/ Analog I/P, 82kΩ to GND/ V, 220Ω GND/A Input
5 Digital I/P/ Analog I/P, 82kΩ to GND/ V, 220Ω GND/A Input
6 Digital I/P/ Analog I/P, 82kΩ to GND/ V, 220Ω GND/A Input
7 Digital I/P/ Analog I/P, 82kΩ to GND/ V, 220Ω GND/A Input
8 Digital In / Analog In, 19.5kΩ to GND & +5VDC Input
9 + Aux Out (Ref 4A)
10 Ground
11 Ground
12 Ground
13 Ground
14 Digital Input, 2.2KΩ to +5VDC Input
15 Must be left Open N/A
16 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
17 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
18 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
19 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
20 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
21 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
22 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
23 Digital Input/ Pulse Input, 2.2KΩ to +5VDC Input
 
Pin Connector 4 Pin Function Type
1 Power Ground
2 CAN 1 HIGH I/O
3 Power Ground
4 VSUPPLY (+9 to 30 VDC)
5 VSUPPLY (+9 to 30 VDC)
6 CAN 1 LOW I/O
7 CAN 2 HIGH I/O
8 CAN 2 LOW I/O

DIMENSIONS:

ECU-2415A Controller Dimensions

  MOUNTING:

ECU-2415A Mounting


The mounting positions shown here will allow water or other potential contaminants to fall away from connectors.

Allow 5 in./125 mm clearance from mounting surface for connector installation.

For additional mounting information, consult the
ECU-2415A Technical Reference Manual.

TO ORDER:
Controller: Model ECU-2415A Part No. 4002723
AmpSeal Connectors: 23-Pin Grey Part No. 4000361; 23-Pin Blue Part No. 4000362
  23-Pin Black Part No. 4000360; 8-Pin Black Part No. 4000363
AmpSeal Socket/Plug: Sockets Gold (100 pc.) Part No. 4000369; Sealing Plugs (100 pc.) Part No. 4000370
Shock Cover Kit (optional): Part No. 4206820
AmpSeal Test Leads: (10 each, 24" length) - Part No. 400287
CoDeSys Programming Software: available from HydraForce Electronics Portal as free download.
USB-CAN Adaptor: Part No. 4000371, also available from
Diagnostic Kit: Part No. 4000372

Electronic Vehicle Controls – Intro. & Contents HydraForce Electronics Guide (all models) – PDF file
Valve Coils and Valve Controllers – Contents PDF file of this page Request a quote