Languages

Pressure Control Valves

CRV10-22 — Cross-Over Relief, Differential Area, Valve Manifold
   Selection guide - similar valves.
  PDF file of this page.
  Request a quote.

CRV10-22 Valve

SYMBOL:
CRV10-22 Valve symbol

 DESCRIPTION
The CRV10-22 cross-port relief uses two RV10-22 cartridges in an in-line plumbed
housing. It is typically used to protect a hydraulic cylinder or motor from load-induced
pressure surges. The cartridges used are screw-in, direct-acting, poppet-type valves,
intended for use in hydraulic circuits requiring low internal leakage.

OPERATION
The CRV10-22 manifold allows flow to pass through the separated 1 to 2 passages at
low pressure loss. If pressure in either passage exceeds the valve setting, flow will cross
over to the opposite passage.
Note: Back-pressure at the outlet port of the relief cartridges will increase the nominal
setting of the valve on a 1:1 basis. For example, 6.9 bar/100 psi back-pressure increases
the nominal setting by 6.9 bar/100 psi.
See valve model RV10-22, page 6.050.1 for cartridge specifications.

FEATURES
• Adjustments cannot be backed out of the valve.
• Adjustments prevent springs from going solid.
• Hardened poppet and cage for long life.
• Optional spring ranges to 240 bar (3500 psi).
• Rapid response to pressure surges.
• Industry-commom cavity size.

RATINGS
Operating Pressure: 240 bar (3500 psi) maximum
Flow: 113 lpm (30 gpm) maximum; see performance chart for flow handling capacity at max.
   setting for each spring range option. Pressure rise will vary with spring (range) and with
   setting within range due to flow forces. Consult factory for specific flow characteristic values.
Pressure Rise: 0.34 bar per liter (5 psi per gallon)
Internal Leakage: 0.25 cc per minute (5 drops/minute) max. to 85% of nominal setting
Crack Pressure Defined: bar (psi) evident at 0.95 lpm (0.25 gpm) attained
Standard Spring Ranges:
Spring Model Code Spring Ranges
6 6.9 to 41.4 bar (100 to 600 psi) at 90% crack vs. reseat accuracy
13 10.3 to 89.7 bar (150 to 1300 psi) at 90% accuracy
25 34.5 to 172.4 bar (500 to 2500 psi) at 90% accuracy
35 34.5 to 241.4 bar (500 to 3500 psi) at 90% accuracy
Temperature: -40° to 100°C (-40° to 212°F) with Buna seals;
   -26° to 204°C (-15° to 400°F) with Fluorocarbon seals
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
   7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Seal Kit: SK10-2x-M for cross-over relief application, 2 required; See page 8.650.1
Body Part Number: 7070170

PERFORMANCE:

CRV10-22 Flow-Pressure		   DIMENSIONS:

CRV10-22 Valve Dimensions

MATERIALS:

Cartridges: (2 required) Weight each:
0.23 kg (0.50 lb); Steel with hardened work surfaces. Zinc-plated exposed surfaces; Buna N O-rings and Fluorocarbon back-ups standard. Anodized aluminum knobs.

Standard Ported Body:
Weight: 0.50 kg (1.10 lb); Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi).

Adjustment Option Details:
See page 6.003.1
Note: European manufactured version
may differ in design/dimensions.
Consult HydraForce Hydraulics Ltd.		   ORDERING CHART:

CRV10-22 Ordering Chart

Selection guide - similar valves.
 PDF file of this page. Request a quote.