Electro-Proportional Valves — Directional Control

SPCL10-32 — Poppet-Type, 3-Port, Normally Closed
with Non-Isolated Load Sense
  Selection guide - similar valves.
  PDF file of this page.
  Valve Features and Benefits.
  STP file for SPCL10-32.
  Request a quote.
SPCL10-32 Valve
U.S. Patent 7,921,880


SPCL10-32 Valve symbol
A solenoid-operated, 3-port, normally closed, poppet-type, proportional, screw-in
hydraulic cartridge valve with an integral, non-isolated load signal to pilot counterbalance
or other control valves in bridge circuit applications.

When de-energized, the SPCL10-32 blocks flow at all ports. When energized,
proportionally-regulated flow is allowed from 3 to 1 with a load-sense signal supplied
at 2. Reverse flow is not allowed from 1 to 3. When using this valve in bridge circuits,
seals should not be used on the pilot pistons of the pilot-operated check valves. This
is to avoid trapping oil which would keep the pilot-operated check valve open.
Note: If low voltage is expected on the machine, 12 or 24 volt systems will require the
use of 10 volt or 20 volt coils respectively.
See “SP Valves and Coil Operating Parameters,” page 2.002.1_pdf.

• Continuous-duty rated coil.
• Efficient wet-armature construction.
• Optional waterproof E-Coils rated up to IP69K.
• Industry common cavity.
• Reduce manifold space claim.

Operating Pressure: 250 bar (3625 psi); Holding pressure at port 1: 350 bar (5000 psi)
Flow: Up to 57 lpm (15 gpm)
Internal Leakage: Ports 1 and 3: 5 drops/minute max. at 250 bar (3625 psi);
   Port 2: 10 drops/minute max. at 250 bar (3625 psi)
Temperature: -40° to 100°C (-40° to 212°F) with Buna seals;
   -26° to 204°C (-15° to 400°F) with fluorocarbon seals;
   -54° to 107°C (-65° to 225°F) with polyurethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC;
   0.18 amps at 115 VAC (full wave rectified).
   E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
   7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: VC10-3, Variation 'B'; See page 9.110.1_3w
Cavity Tool: CT10-3xx; See page 8.600.1
Seal Kit: SK10-3x-MM; See page 8.650.1
Coil Nut: Part no. 7004400

The EVDR Series controllers are recommended for use with most HydraForce
proportional valves. These newer electronic controllers are versatile, reliable,
and easily configured and customized for a wide range of applications.
For the EVDR Product Selection Guide, see page 3.450.1_pdf
For other Electronic Controllers, see page 2.001.1_pdf




SPCL10-32 performance charts


SPCL10-32 performance charts



SPCL10-32 Valve Dimensions



Cartridge: Weight: 0.2 kg (0.44 lb);
Steel with hardened work surfaces.
Zinc-plated exposed surfaces; Buna N
O-rings and polyester elastomer back-up

Standard D-Coil: Weight each: 0.27 kg
(0.60 lb); Unitized thermoplastic
encapsulated, Class H high temperature
magnetwire. See page 3.200.1_10-size.

E-Coil: Weight: 0.41 kg (0.9 lb); Perfect
wound, fully encapsulated with rugged
external metal shell; Rated up to IP69K with
integral connectors.
See page 3.400.1_10-size.



SPCL10-32 Ordering Chart Manual Override options