Solenoid-Operated On/Off Valve HyPerformance™

HSV10-20 — Poppet-Type, 2-Way, Normally Closed
  Selection guide - similar valves.
  PDF file of this page.
  Request a quote.

HSV10-20 Valve

SYMBOL:
HSV10-20 Valve symbol

DESCRIPTION
A solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydraulic cartridge
valve for blocking or load-holding in high pressure applications requiring low internal leakage.

OPERATION
When de-energized, the HSV10-20 acts as a check valve, allowing flow from 1 to 2, while blocking flow
from 2 to 1. When energized, the cartridge’s poppet lifts to open the 2 to 1 flow path. In this mode,
flow from 1 to 2 is severely restricted.
Operation of Manual Override Option: For normal operation (de-energized) the manual override pin
must be seated in the lower detent groove. To shift the valve manually, the operator pushes down on the
knob and rotates 180° in either direction. When the manual override is actuated, increased flow can be
achieved by pulling on the knob.

FEATURES
• Continuous-duty rated coil.
• Hardened seat for long life and low leakage.
• Optional coil voltages and terminations.
• Efficient wet-armature construction.
• Cartridges are voltage interchangeable.
• Waterproof E-Coils rated up to IP69K.
• Unitized, molded coil design.
• 1000-hour salt-spray rated solenoid tubes and coils.
• All HyPerformance products are tested to NFPA specification T2.6.1
  and are tested at a verification level of 90% and an assurance of 99%.

RATINGS
Operating Pressure: 350 bar (5075 psi); 10% cycle life: 420 bar (6090 psi)
   Note: all HyPerformance products are tested for 900K cycles at 350 bar and 100K cycles at 420 bar.
Proof Pressure: 690 bar (10,000 psi)
Burst Pressure: 1380 bar (20,000 psi)
Flow: Up to 75.7 lpm (20 gpm)
Internal Leakage: 0.25 cc/minute (5 drops/minute) max. with 350 bar (5075 psi) at port 2
Temperature: -54° to 107°C (-65° to 225°F) with Urethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Initial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Minimum Pull-in Voltage: 85% of nominal at 350 bar (5075 psi)
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
   7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-2; See page 9.110.1_2w
Cavity Tool: HCT10-2xx; See page 8.600.1
Seal Kit: SK10-2U-O; See page 8.650.1
Coil Nut: Part No. 4553800

PERFORMANCE:

HSV10-20 Valve Performance Chart

  DIMENSIONS:
HSV10-20 Valve Dimensions

MATERIALS:

Cartridge: Weight: (without coil and nut) 0.19 kg (0.41 lb); Steel with hardened work surfaces. Corrosion-resistant zinc-nickel plated exposed surfaces; Urethane O‑ring without back-up standard.

Ported Body: Weight: 1.19 kg (2.62 lb); H‑series ductile iron. Rated to 350 bar (5075 psi).
See page 8.010.1_2w.

E-Coil: Weight: 0.41 kg (0.9 lb); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors.
See page 3.400.1_10-size.
  ORDERING CHART:

HSV10-20 Ordering Chart 10-size E-Coil


Selection guide - similar valves.
PDF file of this page.   Request a quote.