- Services & Support
- Sales & Distribution
Solenoid-Operated On/Off Valve HyPerformance™
HSV10-21 — Poppet-Type, 2-Way, Normally Open
Selection guide - similar valves.|
PDF file of this page.
STP file for HSV10-21.
Request a quote.
A solenoid-operated, 2-way, normally open, poppet-type, screw-in hydraulic cartridge valve,
for blocking or load-holding in high pressure applications requiring low internal leakage.
When de-energized, the HSV10-21 allows flow from 2 to 1, while flow from 1 to 2 is severely restricted.
When energized, the cartridge’s poppet closes on its seat, blocking flow from 2 to 1. In this mode the
cartridge will allow flow from 1 to 2 after overcoming the actuator and spring forces.
Operation of Manual Override Option: The manual override feature is intended for emergency use,
not for continuous duty operation. To shift the valve manually, push and hold down the manual override
• Continuous-duty rated coil.
• Hardened seat for long life and low leakage.
• Optional coil voltages and terminations.
• Efficient wet-armature construction.
• Cartridges are voltage interchangeable.
• Waterproof E-Coils rated up to IP69K.
• Unitized, molded coil design.
• 1000-hour salt-spray rated solenoid tubes and coils.
• All HyPerformance products are tested to NFPA specification T2.6.1
and are tested at a verification level of 90% and an assurance of 99%.
Operating Pressure: 350 bar (5075 psi); 10% cycle life: 420 bar (6090 psi)
Note: all HyPerformance products are tested for 900K cycles at 350 bar and 100K cycles at 420 bar.
Proof Pressure: 690 bar (10,000 psi)
Burst Pressure: 1380 bar (20,000 psi)
Flow: Up to 75.7 lpm (20 gpm)
Internal Leakage: 0.25 cc/minute (5 drops/minute) max. with 350 bar (5075 psi) at port 2
Temperature: -54° to 107°C (-65° to 225°F) with Urethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Initial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC10-2; See page 9.110.1_2w
Cavity Tool: HCT10-2xx; See page 8.600.1
Seal Kit: SK10-2U-O; See page 8.650.1
Coil Nut: Part No. 4555250
Cartridge: Weight: 0.19 kg. (0.41 lbs.);
Steel with hardened work surfaces.
Zinc-plated exposed surfaces; Urethane
O-ring without back-up standard.
Ported Body: Weight: 1.19 kg. (2.62 lbs.);
H-series ductile iron. Rated to 345 bar
(5000 psi). See page 8.010.1_2w.
E-Coil: Weight: 0.41 kg. (0.9 lbs.); Perfect wound, fully encapsulated with rugged
external metal shell; Rated up to IP69K
with integral connectors.
See page 3.400.1_10-size.
|Selection guide - similar valves.
||PDF file of this page.||STP file for HSV10-21.||Request a quote.|