Solenoid-Operated On/Off Valve HyPerformance™

HSV12-21 — Poppet-Type, 2-Way, Normally Open
  Selection guide - similar valves.
  PDF file of this page.
  Request a quote.

HSV12-21 Valve

HSV12-21 Valve symbol

A solenoid-operated, 2-way, piloted, normally open, poppet-type, screw-in hydraulic
cartridge valve, designed to function as a load holding in high-pressure applications
requiring low internal leakage.

When de-energized, the HSV12-2 1 allows flow from ports 2 to 1. while severly restricitng
flow from ports 1 to 2. When energized, the valve's poppet closes on its seat, blocking flow
from ports 1 to 2 after overcoming the actuator and spring forces (See performance graph).

Operation of Manual Override Option: The manual override feature is intended for emergency
use, not continuous duty operation. To shift the valve manually, push and hold down the manual
override button or knob.

Continuous-duty rated solenoid.
Hardened seat for long life and low leakage.
Optional coil voltages and terminations.
Efficient wet-armature construction.
Cartridges are voltage interchangeable.
Manual override option.
Waterproof E-Coils rated up to IP69K.
Unitized, molded coil design.
Corrosion-resistant plating.
Cost effective cavity.
All HyPerformance products are tested to the rigorous standards
  of the NFPA specification T2.6.1.
All HyPerformance valves are tested at a verification level of 90%
  and an assurance of 99%.

Operating Pressure: 350 bar (5075 psi); 10% cycle life: 420 bar (6090 psi)
   Note: All HyPerformance products are tested for 900K cycles at 350 bar and
   100K cycles at 420 bar
Proof Pressure: 690 bar (10,000 psi)
Burst Pressure: 1380 bar (20,000 psi)
Flow: 114 lpm (30 gpm)
Internal Leakage: 7 drops/minute with 350 bar (5075 psi) at port 2
Temperature: -54 to 107C (-65 to 225F) with urethane seals
Coil Duty Rating: Continuous from 85% to 115% of nominal voltage
Initial Coil Current Draw at 20 °C: E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC
Minimum Pull-in Voltage: 85% of nominal at 350 bar (5075 psi)
Filtration: See page 9.010.1
Fluids: Mineral-based or synthetics with lubricating properties at viscosities of
   7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1
Installation: No restrictions; See page 9.020.1
Cavity: HVC12-2; See page 9.112.1_2w
Cavity Tool: HCT12-2XX; See page 8.600.1
Seal Kit: SK12-2U-0; See page 8.650.1
Coil Nut: Part No. 4553800


HSV12-21 Performance Chart

HSV12-21 Valve Dimensions

**Cartridge torque shown for ductile iron manifold. Torque 60-65 ft-lb (81-88 Nm) in aluminum. Aluminum housing is rated to 207bar (3000psi).


Cartridge: Weight: (without coil and nut) 0.29kg (0.63lb) Steel with hardened work surfaces. Corrosion-resistant zinc-nickel plated exposed surfaces. Urethane seals without back-up rings standard.

Standard Ported Body:
Weight: 2.62 kg (1.18lb) H-series ductile iron. Rated to 350 bar (5075 psi).
See page 8.012.1_2w.

E-Coil: Weight: 0.41 kg (0.9 lb); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors..
See page 3.400.1_12-size.

HSV12-21 Ordering Chart

Selection guide - similar valves.
PDF file of this page. Request a quote.